Edit File: _ethtool
#compdef ethtool local -a cmds if [[ $CURRENT -ge 4 ]]; then case $words[CURRENT-1]; in rx|tx) if [[ $words[2] = '-G' ]] && _message -e n 'number of ring entries' || _wanted -x onoff expl 'enabled' compadd off on ;; autoneg|adaptive-rx|adaptive-tx|raw|hex|sg|tso|ufo|gso) _wanted -x onoff expl 'enabled' compadd off on ;; rx-usecs|rx-frames|rx-usecs-irq|rx-frames-irq|tx-usecs|tx-frames|tx-usecs-irq|tx-frames-irq|stats-block-usecs|pkt-rate-low|rx-usecs-low|rx-frames-low|tx-usecs-low|tx-frames-low|pkt-rate-high|rx-usecs-high|rx-frames-high|tx-usecs-high|tx-frames-high|sample-interval|rx-mini|rx-jumbo|offset|length|magic|value|phyad|msglvl) _message -e n 'number' ;; speed) _wanted -x speed expl 'speed' compadd 10 100 1000 ;; duplex) _wanted -x duplex expl 'duplex mode' compadd half full ;; port) _wanted -x port expl 'device port' compadd tp aui bnc mii ;; advertise) _values 'hexidecimal value (or a combination of the following)' \ '0x001[10 Half]' \ '0x002[10 Full]' \ '0x004[100 Half]' \ '0x008[100 Full]' \ '0x010[1000 Half(not supported by IEEE standards)]' \ '0x020[1000 Full]' \ '0x8000[2500 Full(not supported by IEEE standards)]' \ '0x800[10000 Full]' \ '0x03F[Auto]' ;; xcvr) _wanted -x xcvr expl 'transceiver type' compadd internal external ;; wol) _values -s '' 'Wake-on-LAN options' \ '(d)p[Wake on phy activity]' \ '(d)u[Wake on unicast messages]' \ '(d)m[Wake on multicast messages]' \ '(d)b[Wake on broadcast messages]' \ '(d)a[Wake on ARP]' \ '(d)g[Wake on MagicPacket(tm)]' \ '(d)s[Enable SecureOn(tm) password for MagicPacket(tm)]' \ '(p u m b a g s)d[Disable (wake on nothing)]' ;; sopass) _message -e secureon 'password - 6 bytes in ethernet MAC hex format (xx:yy:zz:aa:bb:cc)' ;; file) _wanted files expl 'raw register dump files' _files ;; *) case $words[2]; in -A|--pause) _values -S ' ' -w 'pause options' \ 'autoneg[Specify if pause autonegotiation is enabled]' \ 'rx[Specify if RX pause is enabled]' \ 'tx[Specify if TX pause is enabled]' ;; -C|--coalesce) _values -S ' ' -w 'coalescing settings' \ 'adaptive-rx' 'adaptive-tx' \ 'rx-usecs' 'rx-frames' 'rx-usecs-irq' 'rx-frames-irq' \ 'tx-usecs' 'tx-frames' 'tx-usecs-irq' 'tx-frames-irq' \ 'stats-block-usecs' \ 'pkt-rate-low' \ 'rx-usecs-low' 'rx-frames-low' \ 'tx-usecs-low' 'tx-frames-low' \ 'pkt-rate-high' \ 'rx-usecs-high' 'rx-frames-high' \ 'tx-usecs-high' 'tx-frames-high' \ 'sample-interval' ;; -G|--set-ring) _values -S ' ' -w 'ring parameters' \ 'rx[Change number of ring entries for the RX ring]' \ 'rx-mini[Change number of ring entries for the RX Mini ring]' \ 'rx-jumbo[Change number of ring entries for the RX Jumbo ring]' \ 'tx[Change number of ring entries for the TX ring]' ;; -d|--register-dump) _values -S ' ' -w 'register dump options' \ 'hex[dump hex register data]' \ 'raw[dump raw register data]' \ 'file[use contents from file rather than device]' ;; -e|--eeprom-dump) _values -S ' ' -w 'EEPROM dump options' \ 'raw[dump raw EEPROM data]' \ 'offset[dump certain portions of the EEPROM]' \ 'length[dump certain portions of the EEPROM]' ;; -E|--change-eeprom) _values -S ' ' -w 'EEPROM values' \ 'magic[device-specific key]' \ 'offset[select byte]' \ 'value[new value]' ;; -K|--offload) _values -S ' ' -w 'offload options' \ 'rx[Specify if RX checksumming is enabled]' \ 'tx[Specify if TX checksumming is enabled]' \ 'sg[Specify if scatter-gather is enabled]' \ 'tso[Specify if TCP segmentation offload is enabled]' \ 'ufo[Specify if UDP segmentation offload is enabled]' \ 'gso[Specify if generic segmentation offload is enabled]' ;; -p|--identify) if [[ $CURRENT -eq 4 ]] && _message -e length 'seconds' ;; -t|--test) _values -S ' ' -w 'selftest option' \ '(online)offline:perform full set of tests possibly causing normal operation interruption (default)]' \ '(offline)online:perform limited set of tests do not interrupting normal adapter operation]' ;; -s|--change) _values -S ' ' -w 'change setting' \ 'speed[Set speed in Mb/s]' \ 'duplex[Set full or half duplex mode]' \ 'port[Select device port]' \ 'autoneg[Specify if autonegotiation is enabled]' \ 'advertise[Set the speed and duplex advertised by autonegotiation]' \ 'phyad[PHY address]' \ 'xcvr[Select transceiver type]' \ 'wol[Set Wake-on-LAN options]' \ 'sopass[Set the SecureOn(tm) password]' \ 'msglvl[Set the driver message level]' ;; esac ;; esac fi cmds=(-h -a -A -c -C -g -G -i -d -e -E -k -K -p -r -S -t -s --help --show-pause --pause --show-coalesce --coalesce --show-ring --set-ring --driver --register-dump --eeprom-dump --change-eeprom --show-offload --offload --identify --negotiate --statistics --test --change) _arguments \ "($cmds)1:interface:_net_interfaces" \ "($cmds 1)"{-h,--help}'[shows a short help message]' \ "($cmds)"{-a,--show-pause}'[queries the specified ethernet device for pause parameter information]' \ "($cmds)"{-A,--pause}'[change the pause parameters of the specified ethernet device]' \ "($cmds)"{-c,--show-coalesce}'[queries the specified ethernet device for coalescing information]' \ "($cmds)"{-C,--coalesce}'[change the coalescing settings of the specified ethernet device]' \ "($cmds)"{-g,--show-ring}'[queries the specified ethernet device for RX/TX ring parameter information]' \ "($cmds)"{-G,--set-ring}'[change the RX/TX ring parameters of the specified ethernet device]' \ "($cmds)"{-i,--driver}'[queries the specified ethernet device for associated driver information]' \ "($cmds)"{-d,--register-dump}'[retrieves and prints a register dump for the specified ethernet device]' \ "($cmds)"{-e,--eeprom-dump}'[retrieves and prints an EEPROM dump for the specified ethernet device]' \ "($cmds)"{-E,--change-eeprom}'[Changes EEPROM byte for the specified ethernet device]' \ "($cmds)"{-k,--show-offload}'[queries the specified ethernet device for offload information]' \ "($cmds)"{-K,--offload}'[change the offload parameters of the specified ethernet device]' \ "($cmds)"{-p,--identify}'[initiates adapter-specific action intended to identify the adapter by sight]' \ "($cmds)"{-r,--negotiate}'[restarts auto-negotiation on the specified ethernet device]' \ "($cmds)"{-S,--statistics}'[queries the specified ethernet device for NIC- and driver-specific statistics]' \ "($cmds)"{-t,--test}'[executes adapter selftest on the specified ethernet device]' \ "($cmds)"{-s,--change}'[allows changing some or all settings of the specified ethernet device]' \ '*:' && ret=0
Back to File Manager